宽温域下柔性接头界面损伤及密封可靠性数值研究

doi:10.13675/j.cnki. tjjs. 190136

推进技术 ›› 2019, Vol. 40 ›› Issue (10): 2313-2324.DOI: 10.13675/j.cnki. tjjs. 190136

• Structure, Strength and Reliability • 上一篇下一篇

宽温域下柔性接头界面损伤及密封可靠性数值研究

史宏斌¹,王才¹,屈转利¹,李国才¹

西安航天动力技术研究所，燃烧、热结构和内流场重点实验室

发布日期:2021-08-15

Numerical Research on Interfacial Damage and Sealing Reliability of Flexible Joint under Wide Temperature Range

Science and Technology on Combustion,Internal Flow and Thermo-Structure Laboratory, Xi’an Aerospace Solid Propulsion Technology Institute,Xi’an 710025,China

Published:2021-08-15

摘要/Abstract

摘要： 界面失效是固体火箭发动机柔性接头的重要问题。为研究宽温域（-55℃～65℃）下柔性接头摆动过程中界面的损伤规律，基于ABAQUS 6.14建立了柔性接头的三维非线性有限元分析模型，并采用内聚力模型作为粘接界面的本构模型，获得了界面的损伤参数。此外，结合界面间的接触应力，提出了一种计算柔性接头密封可靠度的方法。结果表明，宽温域下粘接界面与丁异戊橡胶的力学性能随温度的升高而逐渐下降，说明柔性接头在高温段更容易发生失效；并且确认了柔性接头密封可靠度与界面损伤间成反比关系，宽温域下随着温度升高，柔性接头损伤程度先缓慢增大，-40℃后出现迅速增加，而柔性接头密封可靠度先呈线性下降趋势，20℃后下降趋势放缓，-55℃时柔性接头密封可靠度最大。

关键词: 柔性接头;界面损伤;内聚力模型;密封可靠性;宽温域

Abstract: Interfacial failure is a serious problem in the solid rocket motor flexible joint. In order to investigate the damage rules of bonding interfaces during flexible joint swinging under wide temperature range (-55℃～65℃), a three-dimensional non-linear finite element analysis was established based on ABAQUS 6.14. Cohesive zone model was adopted as the constitutive model of adhesive to obtain the damage parameters. Additionally, combined with the interfacial contact stress, one computational method to calculate the sealing reliability of flexible joint was proposed. Results illustrate that the mechanical behavior of adhesive and butyl isoprene rubber both decrease gradually with the increase of temperature, indicating that fracture occurs easily at a high temperature. The correspondence relationship between sealing reliability and interfacial damage is confirmed to be inversely related. The damage of flexible joint increases gradually first and grows rapidly above -40℃ with temperature raising, while the sealing reliability presents a linear downward trend first and then slows down above 20℃ with temperature. The sealing reliability reaches maximum at -55℃ under wide temperature range.

Key words: Flexible joint;Interfacial damage;Cohesive zone model;Sealing reliability;Wide temperature range

史宏斌,王才,屈转利,李国才. 宽温域下柔性接头界面损伤及密封可靠性数值研究[J]. 推进技术, 2019, 40(10): 2313-2324.

SHI Hong-bin¹,WANG Cai¹,QU Zhuan-li¹,LI Guo-cai¹. Numerical Research on Interfacial Damage and Sealing Reliability of Flexible Joint under Wide Temperature Range[J]. Journal of Propulsion Technology, 2019, 40(10): 2313-2324.

参考文献

[1] 阮崇智 . 战术导弹固体发动机的关键技术问题[J]. 固体火箭技术, 2002， 25(2)： 8-12.
[2] Robert F . H， Woodberry . Flexible Joints for Thrust Vector Control[R]. AIAA 75-1221.
[3] Bugrova A I ， Bugrov G E ， Bishaev A M ， et al . Experimental Investigation of Thrust-Vector Deviation in a Plasma Thruster[J]. Technical Physics Letters， 2014， 40(2): 161-163.
[4] Olsen K E ， Walsh J J ， Thomas E L . Navy Terrier LEAP Third-Stage Propulsion[C]. Monterey: AIAA Missile Science Conference， 1994.
[5] Uhrig G ， Roussille C . Design Drivers and Technologies for Solid Propulsion of Interceptors[C]. Arcachon: 1st AIAA International Conference on Missile Defense， 2003.
[6] Caveny L H ， Geisler R L ， Ellis R A ， al et . Solid Rocket Enabling Technologies and Milestones in the United States[J]. Journal of Propulsion and Power， 2003， 19: 1038-1066.
[7] Descamps C ， Gautronneau E ， Rousseau G ， et al . P80 SRM Low Torque Flex-Seal Development， Thermal and Chemical Modeling of Molding Process[J]. EDP Science， 2013， 2009: 141-152.
[8] Boury D ， Gautronneau M ， Daurat， al at . P80 Nozzle Development & Qualification Synthesis[C]. Hartford: 44th AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit， 2008.
[9] REN Jun-xue ， ZHANG Xiao-guang ， YANG Jing-xian ， et al . Structural Analysis and Testing of a Miniature Flexible Joint under Pressure and Vector Loading[J]. Journal of Mechanicaal Science and Technology， 2014， 28: 3637-3643.
[10] SU Hao ， REN Jun-xue ， XUE Mu-yao ， et al . Influence of Pressure and Deflection Loads on the Critical Behavior of Flexible Joint[J]. Composite Structures， 2017， 180: 772-781.
[11] 曹翠微，陈伟民，蔡体敏，等 . 固体火箭发动机柔性接头的结构分析[J]. 推进技术， 2006， 27(5): 450-454.
[12] 王春光，史宏斌，王雪坤，等 . 高压下喷管柔性接头摆动力矩数值分析[J]. 推进技术， 2011， 32(2): 202-206.
[13] 黄朝晖，张潇，刘伟凯 . 基于弧长法对柔性接头高压下屈曲响应研究[J]. 导弹与航天运载技术， 2017， 4: 102-106.
[14] 安春利，常新龙 . 柔性接头弹性件超弹性本构参数拟合和低压摆动非线性有限元分析[J]. 固体火箭技术， 2008， 31(1): 79-83.
[15] 王周成，李耿，陈妮，等 . 容压对柔性接头摆动密封可靠性的影响[J]. 固体火箭技术， 2016， 39(3): 337-341.
[16] F M da Silva Lucas ， Adams R D . Measurement of the Mechanical Properties of Structural Adhesives in Tension and Shear Over a Wide Range of Temperature[J]. Journal of Adhesive Science and Technology， 2005， 19(2): 109-141.
[17] Caggiano A ， Schicchi D S ， Etse G ， et al . Meso-Scale Response of Concrete under High Temperature Based on Coupled Thermo-Mechanical and Pore-Pressure Interface Modeling[J]. Engineering Failure Analysis， 2018， 85: 167-188.
[18] Clemence Vernier ， Marc Dressler ， Hans-Peter Seebich ， et al . Reliability of a Dual-Curable Adhesive Bond[C]. Germany: 17th International Conference on Thermal， Mechanical and Multi-Physics Simulation and Experiments in Microelectronics and Microsysterms， 2016.
[19] XU Yang-jian ， ZHAO Shuai ， JIN Guo-hui ， et al . Explicit Dynamic Fracture Simulation of Two-Phase Materials Using a Novel Meso-Structure Modelling Approach[J]. Composite Structures， 2019， 208: 407-417.
[20] Yang Q D ， Thouless M D ， Ward S M . Elastic-Plastic Mode-II Fracture of Adhesive Joint[J]. International Journal of Solids and Structures， 2001， 38(19): 3251-3262.
[21] Khoramishad H ， Crocombe A D ， Katnam K B ， et al . Predicting Fatigue Damage in Adhesively Bonded Joints Using a Cohesive Zone Model[J]. International Journal of Fatigue， 2010， 32(7): 1146-1158.
[22] Dugdale D S . Yielding of Steel Sheets Containing Slits[J]. Journal of Mechanical Physics and Solids， 1960， 8(2): 100-108.
[23] Barenblatt G I . The Mathematical Theory of Equilibrium Cracks in Brittle Fracture[J]. Advances in Applied Mechanics， 1962， 7: 55-125.
[24] Benzeggagh M L ， Kenane M . Measurement of Mixed-Mode Melamination Fracture Toughness of Unidirectional Glass/Epoxy Composites with Mixed-Mode Bending Apparatus[J]. Composite Science and Technology， 1996， 56: 439-449.
[25] De Moura M ， Goncalves J P M . Cohesive and Continuum Mixed-Mode Damage Models Applied to the Simulation of the Mechanical Behavior of Bonded Joints[J]. International Journal of Adhesion and Adhesive， 2008， 28(8): 419-426.
[26] Yang Q D ， Thouless M D . Mixed-Mode Fracture Analysis of Plastically-Deformation Adhesive Joints[J]. International Journal of Fracture， 2001， 110(2): 175-187.
[27] Floros I ， Tserpes K . Fatigue Crack Growth Characterization in Adhesive CFRP Joint[J]. Composite Structures， 2019， 207: 531-536.
[28] HONG Yang ， YAN Ying ， TIAN Zi-yang ， et al . Mechanical Behavior Analysis of 3D Braided Composite Joint Via Experiment and Multiscale Finite Element Method[J]. Composite Structures， 2019， 208: 200-212.
[29] 贾登，郑健，陈雄，等 . 三元乙丙橡胶薄膜黏接界面温度相关性力学性能[J]. 航空动力学报， 2016， 31(11): 2809-2816.
[30] Walader Tomas ， Biel Anders ， Stigh Ulf . Temperature Dependence of Cohesive Laws for an Epoxy Adhesive inMode I and Mode II Loading[J]. International Journal of Fracture， 2013， 183: 203-221.
[31] Williams J G . Large Displacement and End Block Effects in the “DCB” Interlaminar Test in Modes:I and II[J]. Journal of Composite Material， 1987， 21(4): 330-347.
[32] Blackman B ， Kinloch A ， Paraschi M ， et al . Measuring the Mode I Adhesive Fracture Energy GIC of Structural Adhesive Joints: the Results of an International Round-Robin[J]. International Journal of Adhesion and Adhesive， 2003， 23(4): 293-305.
[33] 乔玉，周光明，刘伟先，等 . 复合材料阶梯形胶接接头渐进损伤分析[J]. 南京航空航天大学学报， 2014， 46(4): 632-637.
[34] Chandrathilaka E R K ， Gamage J C P H ， Fawzia S . Mechanical Characterization of CFRP/Steel Bond Cured and Tested at Elevated Temperature[J]. Composite Structures， 2019， 207: 471-477.
[35] De Moura M ， Goncalves J P M . Cohesive and Continuum Mixed-Mode Damage Models Applied to the Simulation of the Mechanical Behavior of Bonded Joints[J]. International Journal of Adhesion and Adhesive， 2008， 28(8): 419-426.
[36] Shahzad M ， Kamran A ， Siddiqui M Z ， et al . Mechanical Characterization and FE Modeling of a Hyperelastic Material[J]. Journal of Materials， 2015， 18(5): 918-924.

宽温域下柔性接头界面损伤及密封可靠性数值研究

Numerical Research on Interfacial Damage and Sealing Reliability of Flexible Joint under Wide Temperature Range

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价